My new sapp..making a start on a make over
The following users liked this post:
lee2cossies (04-01-2017)
#164
Yes my sig is far to big, I will try and resize it when I get a chance.
CheeRS.Lee.
#166
Strip down the bay today, Removed the turbo, exhaust manifold and trouser section.Removed downpipe to weld the lambda boss, all pulleys removed and belts.
oil breather tank, expansion tank and swirl pot all removed with all hoses.PAS resovoir, PAS pump and alternator all removed, washer bottle.Intercooler and rad out to.
Coil, plug leads and cap/rotor arm out.Front inner plastic wheel arch liners removed.Inlet manifold, plenum, injectors and ecu all off.
Few pics of the bay, it's all looking a bit bare now.
Turbo and intercooler out.
Ecu removed.
Thanks. Lee.
oil breather tank, expansion tank and swirl pot all removed with all hoses.PAS resovoir, PAS pump and alternator all removed, washer bottle.Intercooler and rad out to.
Coil, plug leads and cap/rotor arm out.Front inner plastic wheel arch liners removed.Inlet manifold, plenum, injectors and ecu all off.
Few pics of the bay, it's all looking a bit bare now.
Turbo and intercooler out.
Ecu removed.
Thanks. Lee.
Last edited by 1374lee; 06-07-2017 at 06:36 PM.
#168
The bay is very solid, just a build up of the usual dust/dirt/grease etc over time,it is very good in there, so that is a good start anyway.
I also think it has 4wd pistons in it as it's so quiet on cold start up, it's sounds like a dream.Gonna check the pistons type,having a look with a bore scope soon just to confirm this.
Thanks. Lee.
I also think it has 4wd pistons in it as it's so quiet on cold start up, it's sounds like a dream.Gonna check the pistons type,having a look with a bore scope soon just to confirm this.
Thanks. Lee.
Last edited by 1374lee; 05-02-2017 at 10:07 AM.
#173
Did a bit of cleaning today.Here is what I was faced with.Lots of parts already gone off for zinc coating, blasting etc.
This lot is ready for powdercoating, got some more to add to the pile yet though.
Thanks.Lee.
This lot is ready for powdercoating, got some more to add to the pile yet though.
Thanks.Lee.
Last edited by 1374lee; 05-07-2017 at 08:19 PM.
#178
Part of the Furniture
#180
Advanced PassionFord User
Nice work Lee.
Is your inlet bead blasted or painted?
Cheers Paul
Is your inlet bead blasted or painted?
Cheers Paul
#182
Steve, I know, this is the question people who know me ask me, I can't go through this again, so my answer is yes I am.
Hows the Focus treating you? It was good to see you at Donny.
Soda blasted.
Thanks Paul.
CheeRS.Lee.
Hows the Focus treating you? It was good to see you at Donny.
Soda blasted.
Thanks Paul.
CheeRS.Lee.
Last edited by 1374lee; 08-02-2017 at 04:06 PM.
#183
Exhaust manifold and trouser blasted then put through for the finishing application.
Turbo front housing, thermostat housing and throttle body all going for blasting and finishing product, now all finished and ready to go.
Thanks. Lee.
Turbo front housing, thermostat housing and throttle body all going for blasting and finishing product, now all finished and ready to go.
Thanks. Lee.
Last edited by 1374lee; 05-07-2017 at 08:01 PM.
#184
Part of the Furniture
Exhaust manifold and trouser blasted then put through for the finishing application.
Turbo front housing off and a bit of fettling as somebody had cut off the 4wd actuator bracket, well some shape, it's now been rounded off nicely.
Turbo front housing, thermostat housing and throttle body all going for blasting and finishing product, now all finished and ready to go.
Thanks. Lee.
Turbo front housing off and a bit of fettling as somebody had cut off the 4wd actuator bracket, well some shape, it's now been rounded off nicely.
Turbo front housing, thermostat housing and throttle body all going for blasting and finishing product, now all finished and ready to go.
Thanks. Lee.
#186
I've found that life I needed.. It's HERE!!
that soda blasting leaves a great finish look forward to seeing it all bolted back up love the pics of all the bits you've got together
#189
Front arches, thought I would give them a clean up today as the plastic arch liners are already removed,lots of waxoyl in there, cleaned some off but left some of it in place.Pics before cleaning.
Exhaust is off so thought I would give it a go, first off used Mr Muscle oven cleaner, sprayed it on and left it on for 30 mins.
More pics shortly.
Exhaust is off so thought I would give it a go, first off used Mr Muscle oven cleaner, sprayed it on and left it on for 30 mins.
More pics shortly.
Last edited by 1374lee; 05-07-2017 at 07:36 PM.