Series 1 RS Turbo soon to be track prepared. Update So close to paint now
#126
PassionFord Regular
#128
PassionFord Regular
#129
10K+ Poster!!
iTrader: (9)
All looking good mate
1 concern though is where you have cut your intercooler to modify the pipes!!!!
I did this exact same thing to the grs cooler on my xr2 turbo
I cleaned out all the swarf after but did not realise some had got into the core that I didn't get out and it cost me a 15mile old engine and a 3k repair bill!!! Basilcally the swarf had got into the core during the initial cutting out of the old pipes, I cleaned out all I could see but didn't realise there was swarf I could not see, when the new engine was put in the car and mapped with a bit of boost it blew the swarf out the cooler, into the inlet manifold and then into the head, ruining a valve seat, snapping the valve which fooked the head and the piston and the block! expensive lesson learnt.
So be aware! there is no way when you cut the original pipe out that you can stop swarf getting into that core and it may cost you BIG TIME like it did me!
1 concern though is where you have cut your intercooler to modify the pipes!!!!
I did this exact same thing to the grs cooler on my xr2 turbo
I cleaned out all the swarf after but did not realise some had got into the core that I didn't get out and it cost me a 15mile old engine and a 3k repair bill!!! Basilcally the swarf had got into the core during the initial cutting out of the old pipes, I cleaned out all I could see but didn't realise there was swarf I could not see, when the new engine was put in the car and mapped with a bit of boost it blew the swarf out the cooler, into the inlet manifold and then into the head, ruining a valve seat, snapping the valve which fooked the head and the piston and the block! expensive lesson learnt.
So be aware! there is no way when you cut the original pipe out that you can stop swarf getting into that core and it may cost you BIG TIME like it did me!
#136
I've found that life I needed.. It's HERE!!
Thread Starter
#137
I've found that life I needed.. It's HERE!!
Thread Starter
#140
I've found that life I needed.. It's HERE!!
Thread Starter
To add to the never ending list of problems the turbo doesn't clear anything. The down pipe doesn't clear the gearbox. Easiest solution is to have a Gary crazy cage exhaust manifold made along with a custom down pipe.
#141
Advanced PassionFord User
what turbo are you using mate? im in need of a cossie down pipe if thats what you were going to use
#149
I've found that life I needed.. It's HERE!!
Thread Starter
#152
Spanner monkey
The floor was given 2 coats of U-POL Gravity tex plus stone chip protector in white, then covered in white Hammerite smooth! The arches have had one coat of hammerite and will have a second in a few days.
Dash is going to Central blast.
Dash is going to Central blast.
The following users liked this post:
jessie_rs (28-12-2014)
#153
Part of the Furniture
Join Date: Dec 2009
Location: ivybridge
Posts: 166
Likes: 0
Received 0 Likes
on
0 Posts
Hi, love all the work being put into this car, I like the idea of putting a perspex sunroof in, is that a kit you have bought?, if not what thickness perspex have you used, as i would like to change my rusty glass sunroof
steve
steve
#154
I've found that life I needed.. It's HERE!!
Thread Starter
Hi Steve,
No it was something I had made. The sunroof was mint and didn't needed changing but a track car with a sunroof didn't seem right and I didn't fancy a roof swap!
No it was something I had made. The sunroof was mint and didn't needed changing but a track car with a sunroof didn't seem right and I didn't fancy a roof swap!
#157
I've found that life I needed.. It's HERE!!
Thread Starter