3dr cosworth!! Frozen white, carbon roof, caged, full rebuild an remapped !!15/4/18
#281
10K+ Poster!!
Those door cards look awesome!
#283
PassionFord Regular
Thread Starter
#284
PassionFord Regular
Thread Starter
hi guys been a while been busy/lazy! All brakes fitted an bleed now, non abs,fan,fuel pump looms fitted. Cage an seats fitted had a secs moniter aswel thats in an filter sock. exhaust system an other bits are on she even turns over!! Had to make my own turbo brace an heater matrix to thermo pipe. few bits i been collecting to L8, seimens 83s, pf09, etc an for my next build few other bit let pics do the talking!An thanks to lee2cossies for sorting my brakes out!
#287
PassionFord Regular
Thread Starter
Bit of bad news, getting it all up an ready for a remap an she bent 2valves so having a rebuild now so not much to update but will wen i get time an pics!!!
#289
PassionFord Regular
Thread Starter
if u mean the carpet in the back, i just got a black roll off ebay bit longer than i needed an made a template outa cardboard/paper. Then just cut it to shape then spray carpet glued it down but used a foam underlay first before carpet. so all looks smooth turned out good!!
The following users liked this post:
R4N SS (09-12-2016)
#291
PassionFord Regular
Thread Starter
#292
PassionFord Regular
Thread Starter
havent updated in a while as been busy! had the block bored out for new piston an bottom end getting there. got new double valve springs, every bearing, seals, gaskets everything an new t34 an painted block black after cleaning everything. looking good so far!
#293
PassionFord Regular
Thread Starter
Been doing a bit more, my mates got bottom end sorted its all together sump on, new oil pump, gaskets, bearing etc. All valves lapped in an all fitted head can be fitted down now. Hopefully get few more bits on next few days aswel
#294
PassionFord Regular
Thread Starter
running
Few more bits done an a good bit! got it all put together an fitted in, all water, boost pipes, exhaust everything fitted. Gota tidy few bits up, Had a new braided engine loom looks awesome and its all on. Even got the engine running!! So she starts up an everything new so im happy now, new front wheel bearings so be fitted this week an then will be on the floor an moving!!
#295
Passionford Addict
Just read the thread from the start. Looked like you bought her in the nick of time as looked very unloved when you grit her. Done a cracking job on the rebuild and hope it all goes smoothly this time
#298
PassionFord Regular
Thread Starter
Ye defiantly did it was covered in moss! Thanks mate an I hope it does 😂
#302
PassionFord Regular
Thread Starter
its been a while but she is road legal an running now! had to get new brembo front calipers as they went wrong. Been to melwyn evans to have corner setup etc, few hundred miles an go for a remap as done a few already. Just beeing out in it is awesome an people love it! Been to action day on show was a good day i let the pics do the talking. went for a spin as was a nice day an there was another 3dr out so stopped for a chat. also went to pistonheads meet on weekend an there was a bmw e30 m3 evo that was stunning!!
#303
Advanced PassionFord User
That looks great, nice work.
I bet you're loving it.
I bet you're loving it.
#306
Advanced PassionFord User
That is a stunning 3dr mate.
Is it all stripped inside?
Cheers Paul
Is it all stripped inside?
Cheers Paul
#307
PassionFord Regular
Thread Starter
#308
PassionFord Regular
Thread Starter
thanks all!! I am loving it just opening the garage seeing it is awesome😊😊 yes it's stripped I'll get pics up of inside as nearly finished now but looks nice
#309
Advanced PassionFord User
How comes you ditched the gt30 setup buddy?
Cheers Paul
Cheers Paul
#313
Advanced PassionFord User
What a beautiful car, well done
The following users liked this post:
PaulinhoT (08-05-2017)
#315
PassionFord Regular
Thread Starter
mapped
Hi been a while but been busy with stuff and car!
My new brembo front brake calipers had a piston seized in them after the trouble ive had having to get more. So i got them fully rebuilt new pistons, seals, new ferodo ds2500 pads everything even had them dipped a powdercoated. Also the studs on the turbo housing where the downpipe bolts up to had broken off one, so had to be taken off sent back an they sorted that for me. So bit of a ball ache!!!
Sold my seimens 83lbs injectors an got 55lbs instead, had a full service full nut an bolt check an fare few miles an off for mapping.
So it was setup to run 55s, baby board fitted to my l8, air injectors an its goes like hell
Ill get pics up over next few days aswel!
My new brembo front brake calipers had a piston seized in them after the trouble ive had having to get more. So i got them fully rebuilt new pistons, seals, new ferodo ds2500 pads everything even had them dipped a powdercoated. Also the studs on the turbo housing where the downpipe bolts up to had broken off one, so had to be taken off sent back an they sorted that for me. So bit of a ball ache!!!
Sold my seimens 83lbs injectors an got 55lbs instead, had a full service full nut an bolt check an fare few miles an off for mapping.
So it was setup to run 55s, baby board fitted to my l8, air injectors an its goes like hell
Ill get pics up over next few days aswel!
The following users liked this post:
bull-turbo (18-07-2017)
The following users liked this post:
bull-turbo (18-07-2017)
#318
PassionFord Regular
Thread Starter
Thanks for the nice comments!
forgot to mention its been in a promo video for cruise culture its biggest car show in wales i think. Anyway heres a few pics and the one of the escort cosworth behind is at pure ford top 25 parade lap or something an she got picked and Harvey Gibbs escos in background and hes done an amazing job on the car thank you!!!!
forgot to mention its been in a promo video for cruise culture its biggest car show in wales i think. Anyway heres a few pics and the one of the escort cosworth behind is at pure ford top 25 parade lap or something an she got picked and Harvey Gibbs escos in background and hes done an amazing job on the car thank you!!!!
Last edited by bull-turbo; 18-07-2017 at 07:53 PM.
#320
10K+ Poster!!
Wow, what a stunning car and nice to see it being used.
You ought to get a lot more padding on the front cage if not using a crash helmet.
You ought to get a lot more padding on the front cage if not using a crash helmet.