***FRIJJ the White Westy - I'm Declaring it finished!***
18-09-2008, 09:20 PM
#246
.......................
Thread Starter
iTrader: (2)
Join Date: Aug 2005
Posts: 1,848
Likes: 0
Received 0 Likes
on
0 Posts
Plan is to make fixed section to fit around the new RAC roll bar then have an opening section so Lee can still get to his packed lunch and teddy bears.
good stuff
If so 
26-09-2008, 10:45 AM
#258
BANNED
BANNED
Join Date: Aug 2004
Location: The beach
Posts: 5,249
Likes: 0
Received 0 Likes
on
0 Posts
28-09-2008, 12:48 AM
#260
.......................
Thread Starter
iTrader: (2)
Join Date: Aug 2005
Posts: 1,848
Likes: 0
Received 0 Likes
on
0 Posts
Back now so progress will be quick again. Fuel system finished today and new rear carbon panel made to fit with boot and the Roll Bar rear sections.
Not bad work given I was in Chicago this time last night!!!
Watch this space for big updates!
Not bad work given I was in Chicago this time last night!!!
Watch this space for big updates!
30-09-2008, 04:37 PM
#264
20K+ Super Poster.
iTrader: (1)
Join Date: May 2003
Location: Essex... and Birmingham!
Posts: 21,512
Likes: 0
Received 0 Likes
on
0 Posts
Update...
AP paddle clutch (thanks Rainbum!, super service) is getting fiitted..
with that on Stu gets to use his favourite toy.... no not the multi speed rampant rabbit deluxe turbo! but his electric engine crane...
I had to leave before it was all bolted up... and the mounts fitted! but it is now!!!
THANKS STU!!! YOU ARE A PROPER LEGEND!!! IT WILL NOT BE FORGOTTEN MATE
Total labour cost for this build so far...AND ITS BEEN ALOT OF HOURS!!! most that you cant see, little bits that needed doing and designing etc etc...
Ł0.00
which is good because we have gone slightly over budget on the mecahnical bits
Plan was JUST some greens and a 3 bar. THAT was it.... oooops!
Stu
AP paddle clutch (thanks Rainbum!, super service) is getting fiitted..
with that on Stu gets to use his favourite toy.... no not the multi speed rampant rabbit deluxe turbo! but his electric engine crane...
I had to leave before it was all bolted up... and the mounts fitted! but it is now!!!
THANKS STU!!! YOU ARE A PROPER LEGEND!!! IT WILL NOT BE FORGOTTEN MATE
Total labour cost for this build so far...AND ITS BEEN ALOT OF HOURS!!! most that you cant see, little bits that needed doing and designing etc etc...
Ł0.00
which is good because we have gone slightly over budget on the mecahnical bits
Plan was JUST some greens and a 3 bar. THAT was it.... oooops!
Stu
30-09-2008, 05:29 PM
#269
.......................
Thread Starter
iTrader: (2)
Join Date: Aug 2005
Posts: 1,848
Likes: 0
Received 0 Likes
on
0 Posts
Yes, very trick. Its the first of a new development batch. Forget Mike Rainbum and his "Crackle Effect".....that so 80's like his hairstyle.
The new look is "WRC Blue Bath Towel"
Less of that Rich........I had just finished eating the 2 tonne piece of cod, large chips and curry sauce that Lee pitched up with!
The new look is "WRC Blue Bath Towel"
Less of that Rich........I had just finished eating the 2 tonne piece of cod, large chips and curry sauce that Lee pitched up with!
01-10-2008, 01:50 PM
#275
PassionFord Post Troll
Join Date: Jul 2005
Location: liverpool
Posts: 2,665
Likes: 0
Received 0 Likes
on
0 Posts
love this project, always wanted a westfield myself.
friend has one with a blade motor in, not amazingly quick but the nosie is second to none.
look forward to seeing it on track!!
good luck fellas
friend has one with a blade motor in, not amazingly quick but the nosie is second to none.
look forward to seeing it on track!!
good luck fellas
