my series 1 ST170 turbo, update 7/1/08
#1
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
my series 1 ST170 turbo, update 7/1/08
well here we go i baught this series 1 about 5 months ago it looked ok on the outside but....
then it went to the body shop to get a few pannels chucked on...
well thats about it so far but its to be continued...
then it went to the body shop to get a few pannels chucked on...
well thats about it so far but its to be continued...
#2
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
ive gone and baught a cts stage 2 + gear box off of a mate for 600 quid, took it home primerd & painted silver then found out that it wont fit a series 1 cos of the gearbox mountings at the front cos it was out of a series two so i'll change the casings to get it in but its just more work isnt it
oh and the body shop has put new front cross member & chassis legs on the front...
oh and the body shop has put new front cross member & chassis legs on the front...
#6
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
small update just got all this off of ebay;
4 spoke rs steering wheel,
ford motorsport boost gauge,
-31 acctuator,
towing eye cover,
spec r battrey cover,
polished coil cover,
& an evolution chip to sell to my mate
ive also baught a full set of polybushes from P.T.S
CHEERS FOR THE COMMENTS
4 spoke rs steering wheel,
ford motorsport boost gauge,
-31 acctuator,
towing eye cover,
spec r battrey cover,
polished coil cover,
& an evolution chip to sell to my mate
ive also baught a full set of polybushes from P.T.S
CHEERS FOR THE COMMENTS
Trending Topics
#9
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
a we update for you;
ive just been to the body shop & seen he has put the passenger side inner wing on also with the windscreen out he has also put a replacement pannel on the scuttle pannel corner, it looks rough just now but this guys work is excelent
he,s also put on the outer sill on the neer side;
the rear arch also needed replaced so away that went on looking loads better than before
the rear bottom quarter pannel has also been replaced
so thats about it so far but i'll definatley be back with more cos this isnt getting put up forsale as an unfinished project i tell ya but its going further than i anticapated
ive just been to the body shop & seen he has put the passenger side inner wing on also with the windscreen out he has also put a replacement pannel on the scuttle pannel corner, it looks rough just now but this guys work is excelent
he,s also put on the outer sill on the neer side;
the rear arch also needed replaced so away that went on looking loads better than before
the rear bottom quarter pannel has also been replaced
so thats about it so far but i'll definatley be back with more cos this isnt getting put up forsale as an unfinished project i tell ya but its going further than i anticapated
#14
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
just went to check on the old chestnut today & guess what... more rust
cc
check that out. the guy before me must have tried to fix the arch with a few bits of tin..how rough is that
he's cut the drivers inner wing out ready for the new one to cum & he's put the new sill on the drivers side aswell;
big update cumming next week
P.S. and ive just baught a set of these escort cossie alloys so this is what look im aiming for...how nice is this (without single wiper & spot lamps)
cc
check that out. the guy before me must have tried to fix the arch with a few bits of tin..how rough is that
he's cut the drivers inner wing out ready for the new one to cum & he's put the new sill on the drivers side aswell;
big update cumming next week
P.S. and ive just baught a set of these escort cossie alloys so this is what look im aiming for...how nice is this (without single wiper & spot lamps)
#21
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Bradz
Looking Good.
That Used to be a Good Clean S1 Back in its day
That Used to be a Good Clean S1 Back in its day
do you know the car yourself mate?
#22
Too many posts.. I need a life!!
Join Date: Oct 2003
Location: Aberdeen.
Posts: 801
Likes: 0
Received 0 Likes
on
0 Posts
I know most S1's in this area Im a Bit of a Bufty when it comes to an S1 or Cosworth having owned a Fair few.
A freind of mine owned that car a good few years back.
Who and Where did u buy it from.
A freind of mine owned that car a good few years back.
Who and Where did u buy it from.
#23
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
i got it from a lad in inverurie called jason addie about 5 months ago. it never had much done to it when i first got it (exhaust, filter,hoses)
its getting all the body work done at cadgers garage just now but im hoping for it to be finished by april, ready for the show season
its getting all the body work done at cadgers garage just now but im hoping for it to be finished by april, ready for the show season
#25
Regular Contributor
iTrader: (1)
Join Date: Apr 2006
Location: Trailer trash in Oman desert, its good honest Guv!
Posts: 243
Likes: 0
Received 0 Likes
on
0 Posts
smitty
Fitlikeeeeeeeeeeeee , good job your getting it repaired if your planning to zvh it ! have you got an engine yet ? are you awa the noo ?
the man fae oar the road ( hatton )
the man fae oar the road ( hatton )
#26
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Re: smitty
Originally Posted by kev new
Fitlikeeeeeeeeeeeee , good job your getting it repaired if your planning to zvh it ! have you got an engine yet ? are you awa the noo ?
the man fae oar the road ( hatton )
the man fae oar the road ( hatton )
#27
Originally Posted by bezo
should have a work warning on this pic!!!!
looks flocking porn!!!!!
it is fookin dog rough now, was gonna buy it back but needs to much work, its in ireland now, well it was about a year ago when i was thinking about buying it back!! the car was painted vauxhall glacier white and it had a 2wd cossie cooler but new owner removed it and replaced the front panel, hence the different colour.
60mm drop with a extra coil chopped off the back springs to get a nice height.
i smashed it after owning it for 10 days
#28
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by tony_turbo
I BUILT THAT BAD BOY! Must be nearly 6 years ago now.
it is fookin dog rough now, was gonna buy it back but needs to much work, its in ireland now, well it was about a year ago when i was thinking about buying it back!! the car was painted vauxhall glacier white and it had a 2wd cossie cooler but new owner removed it and replaced the front panel, hence the different colour.
60mm drop with a extra coil chopped off the back springs to get a nice height.
i smashed it after owning it for 10 days
ive fell in love with that picture since i seen it
#29
koni shocks all round as well, front arch lips were removed completely, and bodykit trimmed right back aswell.
rears were done aswell, inner skin cut out completely and outer skin folded right up against it and seam welded round the edge, could still have 4 grown men in it with no rubbing what so ever. running 215/40x16 tyres. it is a h plate rs turbo shell with mk3 panels on it. running 200brake, 2wd cossie discs on the front and series 2 drums on back.
rears were done aswell, inner skin cut out completely and outer skin folded right up against it and seam welded round the edge, could still have 4 grown men in it with no rubbing what so ever. running 215/40x16 tyres. it is a h plate rs turbo shell with mk3 panels on it. running 200brake, 2wd cossie discs on the front and series 2 drums on back.
#30
Wahay!! I've lost my Virginity!!
Join Date: Jul 2006
Location: Brighton
Posts: 96
Likes: 0
Received 0 Likes
on
0 Posts
that rs on cossie wheels is proper porn!
hats off to you mate for getting it all done...must be costing a pretty penny!
will be worth it in the end!
hats off to you mate for getting it all done...must be costing a pretty penny!
will be worth it in the end!
#31
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mossymk4
that rs on cossie wheels is proper porn!
hats off to you mate for getting it all done...must be costing a pretty penny!
will be worth it in the end!
hats off to you mate for getting it all done...must be costing a pretty penny!
will be worth it in the end!
its always cheeper when you know the right folk
but it is going further than anticapated
but everyone on this page has taken it further than they where expecting
#32
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
update time
i went to check the progress today & was surprised the finger
was pulled out & the drivers inner wing was put on but not before
even more of the dredded rott was foun & patched up also the front pannel was tacked up ready along with the drvers sill....
i went to check the progress today & was surprised the finger
was pulled out & the drivers inner wing was put on but not before
even more of the dredded rott was foun & patched up also the front pannel was tacked up ready along with the drvers sill....
#34
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by kev new
should look good when finished , who's painting it ?? , keep them pics coming
any way a wee update for you as the body shop is taking forever
im gettin realy pissed off now
any way ive gone & got rid of the huge 225-50-16 tyres
in favour of a nice set of 215-40-16 TOYO proxes T1's
there not cheap either at 80 quid a pop but there
the only things keaping you on the road realy...
my mate was selling his series 2 but before he did
i got this home made oil breather tank from it but im
not sure if i'll use it yet
ive also baught a brand new set of hella headlights for the
bargain price of 20 quid
hopefully the body work will be done by christmas
#37
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
ive been buying more stuff off of fleabay to start with i neaded some new dials as mine are pish in the dark so i got a set of these complete lockwood set for £9 so they will do nicely
i also got a double pillar mount for my ford motorsport boost gauge but ive an empty space for another but ive still buy one yet
hopefully the car itself will be finished by xmas promised by the body shop
i also got a double pillar mount for my ford motorsport boost gauge but ive an empty space for another but ive still buy one yet
hopefully the car itself will be finished by xmas promised by the body shop
#39
PassionFord Post Whore!!
Thread Starter
Join Date: Oct 2005
Location: aberdeenshire
Posts: 7,346
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by kev new
hopefully the car itself will be finished by xmas promised by the body shop :roll
Dont bank on it
Dont bank on it