Mtx again
#1
I've found that life I needed.. It's HERE!!
Thread Starter
Mtx again
Been messing about looking into fitting mtx box. got it bolted up to the engine marked it up so I know where to trim the chassis leg.
how do people go about measure for drive shafts. ive got a idea but just want to see how everyone else would go about it.
also ave got a cosworth clutch drive plate if I get a cover will it work?
thanks
lee
how do people go about measure for drive shafts. ive got a idea but just want to see how everyone else would go about it.
also ave got a cosworth clutch drive plate if I get a cover will it work?
thanks
lee
#5
YES I KNOW I CANT SPELL
Join Date: Mar 2008
Location: chingford e4
Posts: 5,271
Likes: 0
Received 0 Likes
on
0 Posts
when i made my shafts i used focus rs shafts and mk2 xr2 shafts i cut all 4 shafts up and used the focus rs inner halfs and the xr2 outer. i measured the width of the 4 half's and had some sleeves made up (crazycage made them for me)
fitted all the bits and sat the car flat on the floor i moved the bits around untill i felt the inner and outer were sitting in the right place.
i then spot welded it stripped it all down welded it all up and refitted it all i then drove the car around on welded shafts for a week or so just to make sure all was good.
i then had the welded shafts copyed and made into one piece shafts
just to add tho the welded shafts took 1bar boost from a gt30 for ages. and the one piece shafts went on to snapping lol
fitted all the bits and sat the car flat on the floor i moved the bits around untill i felt the inner and outer were sitting in the right place.
i then spot welded it stripped it all down welded it all up and refitted it all i then drove the car around on welded shafts for a week or so just to make sure all was good.
i then had the welded shafts copyed and made into one piece shafts
just to add tho the welded shafts took 1bar boost from a gt30 for ages. and the one piece shafts went on to snapping lol
#7
I've found that life I needed.. It's HERE!!
Thread Starter
Trending Topics
#9
I've found that life I needed.. It's HERE!!
Thread Starter
when i made my shafts i used focus rs shafts and mk2 xr2 shafts i cut all 4 shafts up and used the focus rs inner halfs and the xr2 outer. i measured the width of the 4 half's and had some sleeves made up (crazycage made them for me)
fitted all the bits and sat the car flat on the floor i moved the bits around untill i felt the inner and outer were sitting in the right place.
i then spot welded it stripped it all down welded it all up and refitted it all i then drove the car around on welded shafts for a week or so just to make sure all was good.
i then had the welded shafts copyed and made into one piece shafts
just to add tho the welded shafts took 1bar boost from a gt30 for ages. and the one piece shafts went on to snapping lol
fitted all the bits and sat the car flat on the floor i moved the bits around untill i felt the inner and outer were sitting in the right place.
i then spot welded it stripped it all down welded it all up and refitted it all i then drove the car around on welded shafts for a week or so just to make sure all was good.
i then had the welded shafts copyed and made into one piece shafts
just to add tho the welded shafts took 1bar boost from a gt30 for ages. and the one piece shafts went on to snapping lol
#10
PassionFord Post Whore!!
#12
I've found that life I needed.. It's HERE!!
Thread Starter
Well was thinking with the car sitting on the floor with the shaft level i would think it would be at its shoties so the shaft should be sitting canny far in.
#14
PassionFord Post Whore!!
sorry bram , I did get your pm but got side tracked ,I get loads of pm's every day and it takes me ages to work my way through them .
don't bother with the cossie clutch ive yet to see one work properly on a zetec.
don't bother with the cossie clutch ive yet to see one work properly on a zetec.
#15
I've found that life I needed.. It's HERE!!
Thread Starter
No problem mate I gest you would have. What's the problem with the cosworth clutch does cover fit? Ave got a helix 6 paddle drive plate and it fits the flywheel and splins in the box but I haven't got a cosworth cover and the standard mondeo one won't cover the paddle plate.
#16
PassionFord Post Whore!!
[QUOTE=little bram;6329263]No problem mate I gest you would have. What's the problem with the cosworth clutch does cover fit? Ave got a helix 6 paddle drive plate and it fits the flywheel and splins in the box but I haven't got a cosworth cover and the standard mondeo one won't cover the paddle plate.[QUOTE
Not sure mate I've never tried fitting one mate .I no a few people that couldn't get them to hold good power
Not sure mate I've never tried fitting one mate .I no a few people that couldn't get them to hold good power
Thread
Thread Starter
Forum
Replies
Last Post
massivewangers
General Car Related Discussion.
30
01-10-2015 07:40 PM
cossirob
General Car Related Discussion.
10
16-09-2015 07:39 PM