3dr cosworth!! Frozen white, carbon roof, caged, full rebuild an remapped !!15/4/18
#81
PassionFord Regular
Thread Starter
#85
PassionFord Regular
Thread Starter
Hi both nice talking to you both your cars are stunning. I have registered on rsoc but just got to figure out how to use. Thank you for the nice comment to an next year ill be bringing my car when its together lol
#86
PassionFord Regular
Thread Starter
Hi both nice talking to you both your cars are stunning. I have registered on rsoc but just got to figure out how to use. Thank you for the nice comment to an next year ill be bringing my car when its together lol
#87
PassionFord Regular
Thread Starter
#89
PassionFord Regular
Thread Starter
Done a bit more got the nut an bolts i needed aswel cage ones, arb's, beam mount plates an the long 2, strut brace, disc to bells, calipers to hubs an few more. The boot flat floor is done to cage plates next an most things in primer. Pic of the bits i got in rs combe
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#91
PassionFord Regular
Thread Starter
#92
PassionFord Regular
Thread Starter
hi guys been a few weeks, all the cage plates are in an the crumple zones by your feet are welded over. Well all the welding is done on the floor is done the sill, boot floor, cage plates, Jacking point as they were bad etc etc. Also done the back of the car in POR15 the paint is still wet in the pic
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#98
PassionFord Regular
Thread Starter
Thanks for the nice comments! The POR15 is done bar the rear drivers an front arches. I bare metaled it all before the POR15 ino you now what it looks like so wont put a pic up lol. im going away for 10days next tuesday so wont be nothin done for a bit. Had black boost pipes off here aswel. So when im back ill get all the rolling shell stuff done!
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
Last edited by bull-turbo; 25-09-2013 at 07:54 PM.
#99
PassionFord Regular
Thread Starter
#100
PassionFord Regular
Thread Starter
Been doing a bit more the beam, arms, shafts, cross member are painted an some new bolts. Fitted them aswel the diff is clean an ready to fit. New wheel bearings all fitted with the camber shims rear shocks. Its off the spit aswel photobucket is playing up so post some up tomo
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
#104
PassionFord Regular
Thread Starter
#105
PassionFord Regular
Thread Starter
Thanks. Ye its really good stuff I brushed it on but you couldn't tell it was really smooth. A lot of people recomend it if you type it in on YouTube its well known. I'd use it again though if its good for ships it good for cars!
#106
PassionFord Regular
Thread Starter
#108
PassionFord Post Whore!!
Looking good.
Coming along nicely
Coming along nicely
#110
PassionFord Regular
Thread Starter
Thanks ye coming along slowly! The paint on the underside of the shell is POR15 then 3m spray underseal. The beams an cradle etc is jus spray etch prima an gloss black 2pack paint I use a spray gun doing it all!
Last edited by bull-turbo; 01-12-2013 at 06:04 PM.
#112
PassionFord Regular
Thread Starter
hi guys a little bit done as been busy with other things. had a few new bits aswel as im going for gt30 external wastegate an cant wait. new strut brace, 4x4 brake cylinder, sablasted few bits an painted them. had aerocatches to set for the bonnet an boot. An the pro alloy IC i had was faded an dirty so cleaned an painted an cleaned my exhaust to its like new!!
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG][IMG][/IMG]
[IMG][/IMG]
An the good bit that im getting off Lee2cossies the big TURBO on his fresh engine!!
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG]
[IMG][/IMG][IMG][/IMG]
[IMG][/IMG]
An the good bit that im getting off Lee2cossies the big TURBO on his fresh engine!!
[IMG][/IMG]
#115
PassionFord Regular
Thread Starter
#120
PassionFord Regular
Thread Starter