ZetecSX

Hey chaps...

Im new on this forum,

So... my spec will be as follows:

ST150 2.0 Duratec (on 7k, 3k since a full re-build), Titan roller bearing ITB's, webber fuel pressure regulator, uprated fuel pump, St150 gearbox (with built in ERST S2 LSD).. all running on stand alone omex 600 managment (with launch control set up)

This is running circa 187bhp and 149lbfts.. 0-60 in 6.1, (5.9 with the launch control and warm tyres)... and around 198 bhp per tonne

It is mental..lol, love it to bits...

Also have ST front brake set up, with braided hoses...



Anyways here is a few pics, and a cold start video..let me know what you think...













and a video of a very cold start and idle... few revs and stuff in between, whack your headphones in, loads of pops and bangs...


http://www.youtube.com/watch?v=VxFlh...layer_embedded




Also stripping it out over the summer, already bought a roll cage, bucket seats and harnesses...

Plans for over the winter: Shawpeed Cams, Head Work from Caterham or Field Motorsports, HD bolts and uprated Valve springs, and a nice re-map to tie it all in...


Cheers

Tom

ZetecSX

Couple more cheeky ones from FiTP...


















Let me know what you think.... as far as im aware this is the only mk5 zetec-s with the ST and ITB conversion...

ZetecSX

couple more for luck...




and the cage that is having door bars and a further harness bar added... then being sprayed gloss black befroe it goes in...






Seats ive got just the one Cobra Clubman, with a Sabelt 4 point harness....

fiestamad

nice a bit smoky

craigp

looking good mate, bet that shifts

TOMMY_RS

lookking good i like that mate

zetec-Sam

iTrader: (2)

ollies old engine

Twins

iTrader: (18)

Welcome to the site ,looks a right good laugh, bet it goes well

Tev

iTrader: (2)

Your car looks a cracking zetec s!!

I really miss mine!! such a fun car and they handle so well with only a few mods

Brian

iTrader: (2)

Looks very nice mate


Brian

It's Czech Mate

Cracking car mate! Very nice.

ZetecSX

Thanks a lot for all the comments guys….. yeh it is a bit smokey, but that’s mixed with hot air as it was cold when I started her up.. and she hadn’t been started all weekend…

Yeh she goes like stink with the power to weight ratio of just under 200bhp per tonne, she keeps up with a few things she really shouldn’t.. CTR’s, WRX’s, MK1 Focus RS’s etc… she really puts a smile on my face..

Will be even better when I put her in the garage over winter… will be taking her up to shawspeed to set up some cams, valve spring etc… to see the 200bhp mark.. been speaking to john at Shawspeed, and if I get the headwork done before he rekons he could squeeze close to 260 horses from the engine without going to mental… should be interesting..

Just cannot wait to get the cage in and re-strip it again…

Thanks again for all the nice comments, ill be at the RSOC meet at the half way house next week, and will be at Ace café.. soon, so hopefully see some of you there, come say hi…

Cheers

Tom

ZetecSX

Picking up some Carbon fibre wrap tonight to trim a few things up in... should look pretty kool..

Also going to start stripping and welding shit this weekend... so it will be a mad one..

kanabyz

Very Beautiful its Fiesta

ZetecSX

cheers mate.. thanks alot....

Rcjm88

How come you aren't giving the head to Jon to do?

ZetecSX

Only because i know Ben at Kateram, he's a mate of mine who i play rugby with... so he will do it for next to nothing.. i dont know Jon at all....

But it would make sense if i took it up to him for cams, he could work the head as well...

We shall see...

Do you know what cams jon does for the duratec mank..??as id rather order them down my way.. just to save a jounrey up north..

Rcjm88

They are labelled like the cams for the SE I believe, so SS4, SS3, SS5 I think. I don't know any technical info on them though. Give Jon a ring, very helpful bloke, certainly knows what he's doing. The heads I've seen for the SE are very impressive, so I can see the Duratec one's being just as good.

You can order it all from Jon and he can ship it to you to get it fitted elsewhere if needed.

ZetecSX

oh right really ..?? i thought the SS3/4/5 were only for the SE, didnt realise jon did them for the D-Tec as well..

Ill give him a buzz after the summer when i get some more money together... it all depends how much he charges for headwork.. might get the cams, valve springs, HD bolts etc from Jon.. then get the headwork done at Kateram..

Cheers for the info

ZetecSX

Also just a couple of pictures of the half cage and bucket seat ive got to go in...

the half cage is having door bars and harness bars welded in before it goes in fully...

Seats arent amazing condition but you get the jist...

Sp3no

iTrader: (1)

How much of the interior have you stripped to lose over 110kg from the standard Kerb Weight? If its an easy/quick excercies i might consider this for my focus

ZetecSX

The ZS is only about 950 kg to start with then...
-removed rear seats (bench and backs)
-removed all the carpets
-all the sound deadening
-removed Rear Door cards
-Carbon fibre front doorcards
-Carbon fibre wing mirrors
-Removed all plastic trim (a pillars, b pillars, c pillars)
-removed boot skin
-Removed rear wiper and motor
-Removed roof lining
-Seat belts and tensioner
-Spare wheel
-Bucket seats

Basically anything that can be lightened do it... and anything that can be taken off do that.. i litterally have taken loads out, but a lot of people go even lighter.. ie half dash, removing PS, etc

Its very noisey in my car, you can hear everything..lol stripping is defo worth doing in my opinion...

ZetecSX

Kind of looks like this in there atm... (minus the green dial surrounds, adn the standard door cards, and the trim around the doors... oh and the radio comes out some times...) but with 2 standard seats most of the time... i tend to get bored and take stuff out, put stuff back in... at the moment im in a stripped phase..

Pumatt

Nice ZS mate! Makes a nice noise aswell I remember seeing this at FITP.

ZetecSX

Thanks mate, nice one....



Went to the RSOC meet last night and the carbon fibre there was AWESOME… so me and john did my new wing mirror base plates and inside light in CF wrap.. came out amazing, havnt got any pics of the light but will get some pics up as and when

Will also be doing my door handles and a few other bits when I can…

ALSO: When the cage goes in its going to be sprayed satin black.. saw 2 cages last night in satin black and it just goes soooo well imo…

ZetecSX

Messing around with the launch control last night.. lol

http://www.youtube.com/watch?v=ZO5xe...layer_embedded

Psycho Warren

iTrader: (5)

You got much info on the conversion?? ie are the mounts now available off the shelf from various people?? what sort of combination of mk4/5 parts and mk6 parts needed to match up etc??

ZetecSX

Obviously an ST150 engine from a mk6.5 … Custom loom (half mk5, half mk6, with the Omex in it) Custom mounts they are basically puma mounts but modified to fit with a bit of nip and tuck and welding a plate to the bottom to raise it up slightly.. (although these are available off the shelf from a few manufacturers but are about Ł300).. ST150 gearbox with the LSD from a mk6.5, Focus ST170 gear selectors and gear stick…

Some more customising in the gear box as the ZS runs a different style gear box to the ST.. (had to run the selectors through a new hole in the fire wall)

Also a custom manifold to fit the mk6 manifold to the mk5 centre section..

That’s the jist of it all..

ZetecSX

Also custom gearbox mounts... and the gearstick relocated further back to accomdate the selectors

ZetecSX

Fast Ford photo shoot next week..!! keep your eyes peeled over the next couple of months in the mag..

Glenn_

iTrader: (1)

Nice a bet its a hand full.

ZetecSX

yeh its a bubble mate...

ZetecSX

Few pics from the fast ford shoot yesterday.... should be in septembers edition.. so out in August.. woop woop..

packman

You need to run very good air filter setup esp with roller barrels or the dust will score the bore of the barrels and they will stick OPEN and become paper weights .

ZetecSX

thanks mate... ive ordered an ITG sausage filter, just need the backplate made up...

ZetecSX

few more pics.. from a proper camera that was there..

ZetecSX

Nothing much has happened over the last few weeks... few pics and vids of a new exhaust, new seats and ill be getting standard wheels...

going back to the sleeper look..



3.5 in rolled in exhaust, with magnex centre silencer...




Focus ST 170 centre console.. (needs some more bits to finish it) 3 cup holders..!! woop woop





Tangoe side repeators and indicators back in...





New Seats, from a Rover.. not fitted yet, but this is in the previous owners car..




Oil Catch Tank







New Gear nob..




10 seconds on the launch control with the new exhaust..






Cheeky Launch Control Video: http://www.youtube.com/watch?v=w8K6ryGVeTo



Few more bits before Ford Fair to do, but mostly will just be shiney and bufty sessions..

jonny s2

iTrader: (12)

bet that goes well

erjones

Looking good, was that the catch tank you got like stupidly cheap at the Thurrock meet? lol

ZetecSX

Lol..cheers jonny, yeh she does shift and keep up with things that she really shouldnt...

Lol..catch tank was 15quid, got it from a lad on zsoc...

Its annoying at the moment.. question im facing now is do i cam this up, or do i keep it as is and get my dream car.. a sapph cossie..??