Mk6 JWRC fiesta cosworth
#4323
PassionFord Post Whore!!
iTrader: (3)
I'm only saying wot my setup dose and my pressure switch brakes contact at about 500/600psi I'v not modded it in any way and . All MK is trying to do is make the system work as cheap as poss for the time been the same as my self as we don't have ŁŁ to burn . I no it's not the best set up but it gets it working
#4324
Took the car out earlier after checking about the attessa set up with Ian , thanks again mate
Anyway took it out with no attessa set up so full RWD and it was a bit of a handful lol
Leaving proper 11's down the road but steps out sharpish lol had some low speed fun as I feared I would run out of talent
Anyway the box sounds like shit lol, very noisy on over run and part throttle but goes into gear perfect so I suspect bearings but il look into getting a full rebuild soon
Anyway took it out with no attessa set up so full RWD and it was a bit of a handful lol
Leaving proper 11's down the road but steps out sharpish lol had some low speed fun as I feared I would run out of talent
Anyway the box sounds like shit lol, very noisy on over run and part throttle but goes into gear perfect so I suspect bearings but il look into getting a full rebuild soon
#4325
10K+ Poster!!
Not good to be noisey. It is amazing the difference with 2wd vs 4wd. I didn't think it would be that great. I take it that it is the box and not the clutch that is rattling? Mine def seemed to be clutch. If I have to rebuild mine then it will be a close ratio kit for sure.
Last edited by Caddyshack; 18-09-2015 at 08:21 PM.
#4328
10K+ Poster!!
I think I MAY have some of the low pressure side left as I bought spare, I will let you know if I have it as might be useful for sizing?
#4329
I've found that life I needed.. It's HERE!!
When I walked in to my local pirtek to get my pipes crimped I walked out with a lot less cash than I thought. Jesus they know how to charge.
#4330
I will be using aeroquip on the attesa lines, thanks for the offer though
Mounted the reservoir just now on a simple ally bracket nothing flash
Plan is to mount the attesa pump under the passenger seat as there is no room under the car for it, and this will keep all lines nice and short too
Just need to check it will clear the underneath of the seat
Mounted the reservoir just now on a simple ally bracket nothing flash
Plan is to mount the attesa pump under the passenger seat as there is no room under the car for it, and this will keep all lines nice and short too
Just need to check it will clear the underneath of the seat
#4331
10K+ Poster!!
Might be best to mount it so the bleed nipple is easy to get to and wont spill fluid in the car...maybe pipe it out under the car? I used anti vibration mounts as I didn't want too much noise but then mine is a road car.
The following users liked this post:
ossie cossie (22-09-2015)
#4335
Mounted the pump under the passenger seat and it just about fits although I'd need to remove seat to bleed it but that's only 5 mins so no real issue
Just clears seat
Also I finally decided to go for the Full Race ETS PRO
So ordered Friday night from Phoenix Arizona and it turned up Tuesday!!!
Get it all plumbed and wired in next but won't be for a little while yet, well the wiring anyway
Thanks
Marc
Just clears seat
Also I finally decided to go for the Full Race ETS PRO
So ordered Friday night from Phoenix Arizona and it turned up Tuesday!!!
Get it all plumbed and wired in next but won't be for a little while yet, well the wiring anyway
Thanks
Marc
#4336
PassionFord Post Troll
I'll wait until it's finished to pick the box up I want a passenger ride great stuff marc
#4341
PassionFord Post Troll
#4344
I've found that life I needed.. It's HERE!!
That,s a hell of a clean attessa pump, mine looks crap compared to that.
Did i see some where on one of these skyline box threads that someone put up the wiring diagram/ colour codes of the wires on the attessa pump the 6 pin connector.
Did i see some where on one of these skyline box threads that someone put up the wiring diagram/ colour codes of the wires on the attessa pump the 6 pin connector.
#4345
10K+ Poster!!
I did. Just go to the ets pro site and it is all there under installation instruction pdf.
#4350
10K+ Poster!!
I think the ets site has an answer for that. I will have a look.
#4355
Only a small thing but due to exhaust tunnel I put in the handheld fire extinguisher no longer fits tucked under the passenger seat so although not as tucked away it's a top priority for me to have it accessible if ever needed so I mounted it long ways and will make a new foot plate as well
More room than it looks still, worst case scenario passenger might knock the catch but no real dramas
More room than it looks still, worst case scenario passenger might knock the catch but no real dramas
#4356
Lucifer II - 666
looking good pal
#4360
10K+ Poster!!
Wow, that bracket looks soooo cool. Holes are just great!