mk3 escort,2 litre zt 28/3/2010. geting pissed off now still no spark

[rst in breaking]

it should be poss though just more grief and not the preferred way

If you were logged in, you wouldn't be seeing this ad! Register your free account today, or log in if you already have an account.

[Rick]

If your on an MS1 chip, you'll need the high res code for greens, which does need resistors. If you're on an MS2 chip then you can set the PWM current limit to 25% and run without resistors.

Rick.

[danny_boy699]

ffs , any more bad news, any 1 know where ican get a base map put on to run me car.

yes paul you know what will come next

[rst in breaking]

you best tell me, theres a few things it needs to start atm lol

[Rick]

I can send you a base map, but i'll need to know how you are triggering (36-1 i guess), what chip you have and how u are firing the coils, EDIS or direct fire.

Rick.

[danny_boy699]

engine has 1600cvh efi flywheel, probley runing EDIS though zetec coilpack, my ms is ms1 v3. rick if u tell me what you need to know i can tell u but please spek english not to good with all this ecu spek

paul it will end up in a pill of bits last i was gonna do last week

[rst in breaking]

if you do need ballast resistor i think o have some laying around which came with my emerald, but why not opt for some high inpedance injectors instead? probally more variety?

[Rick]

OK, with MS 1, you need resistors for the Greens. If you have any spare cash, get an MS2 chip -about 40 quid - it is much better.

[rst in breaking]

im not to clued up on this ms stuff either so sorry if im complicating things. is there really any difference between them other than not needing ballast resistors?

[danny_boy699]

rick where will i get a ms2 chip from.

same ere paul i not that clued up

[Rick]

This guy will supply you one: http://www.extraefi.co.uk/ms2_products.htm

It's much better, it gives very fine control of big injectors - i ran a totally std 1.6 on greys with this and it idled at 15:1 without the close loop on. Latest codes support fully sequential, individual cylinder trim etc. Code is constantly being updated with new features.

Rick.

[danny_boy699]

so i get this chip thing, then i can run 803's using this with out ballast resistors, then just need a base map to install on my ms to run my car till i get it mapped am i right or am i miles away

[rst in breaking]

why are you soo eager to run greens if you havnt bought them?

[danny_boy699]

been saying from day 1 car will have a zetec with m/s, greens and other things, gonna get some greens next saveing for your turbo, waiting to be payed for a few thing

[rst in breaking]

go high inpedance and it will rub on what you have, probally cost less to buy + more options

[danny_boy699]

been told greens are high inpedance but not sure, gonna get the mk2 chip thing rick was on about then i work it our from there

[Rick]

greens are low impedance.

[danny_boy699]

ah right and ms1 runs high impedance. rick if i send u my ms could you put a base map on it and the ms2 chip thing or ballast resistors, for some coin. i tryed to get it loads up on to my pc today to have a look but it all french to me don't under most of it

[clarke5700]

no edis on your megasquirt mate its wasted spark set up and i have read through the manual the megasquirt you have can run lom imp injectors NO RESTERS NEEDED mite evon be an ms2 lol

[danny_boy699]

Originally Posted by clarke5700

no edis on your megasquirt mate its wasted spark set up and i have read through the manual the megasquirt you have can run lom imp injectors NO RESTERS NEEDED mite evon be an ms2 lol

ah that sort of helps me out a little, but still don't make much senser as i thick as fuck

[danny_boy699]

little update with good pics, fitted my front springs, after cuting 2 coils off but it still to high, and made another addpeter plate for me head and striped it down to be skimed and ported, also fitted a new sticker just for a laugh

[Rick]

Does the rover manifold clear the servo ok? Dropping my engine in over the weekend.

[danny_boy699]

it clears but throttle body it about 3 to 4 mm away but thats when the thottle is closed when it open u have loads of room, but if ya gonna drop ya engine i would say remove in let first or the top half

will get u a pic of my ms up asap fella just i at my parents and my ms is at home 25 miles away

[rst in breaking]

getting there, did you get the damaged wheel repaired?

[danny_boy699]

nah not yet gonna take it in tomorrow to my mate and leave it with hime to get sorted

thanks for the turbo paul

[westus1]

where'd you get the sticker?
i want 1

[danny_boy699]

off ebay mate guy has a site www.slook.com or co.uk

[jonnyrsturbo]

coming on nicely now mate

[danny_boy699]

yeah not far off, it all a case of building it up

[mad dog younge]

Originally Posted by danny_boy699

nah not yet gonna take it in tomorrow to my mate and leave it with hime to get sorted

thanks for the turbo paul

2 moro never comes then eh.as for ms danny you are doing it all wrong.803s are far to big mate .your on the dole and wont be able to afford the fuel to start it never mind run it .my fiesta was at 7 mpg and i had a good job

[rst in breaking]

will try my best to get turbo out before saturday mate, mite look up the wieght and try sort a courier, send me over your address fella

[danny_boy699]

Originally Posted by mad dog younge

2 moro never comes then eh.as for ms danny you are doing it all wrong.803s are far to big mate .your on the dole and wont be able to afford the fuel to start it never mind run it .my fiesta was at 7 mpg and i had a good job

younge not runing 803's any more, not assed on fuel, it being built to be used and kicked from a2b, will nack it from when i start it to when i turn it off, so will use a nuff fuel any

paul no rush for turbo i still ow u 15 when this dick head pay for these wheels

[Glenn.]

Its getting there mate slowly but surely.

[clarke5700]

looking good mate

[danny_boy699]

younge forgot all about bring the wheel, went to weight some scrap in and get the alloys for the corsa, and u know i don't get up till about 1

[mad dog younge]

well danny good luck as you will need it mate .i done a ms conversion last week and booked it in for mapping .thats another point get some one to send you a base map ,,,,and fuck your engine .like i said good luck you will need it.youve got no idea .

[danny_boy699]

only need a base mate to start it, once it runing i geting towed to motorscoop to get maped.

[ScoobyMatt]

Sorry fi this has already been answered..
The MS1 V3 WILL RUN low impedance. You will need to set the injector characsteristics in Megatune.

The PWM time should be 0.1 and the Max current should be around 70%

So to clarify, if you have an MS1 V3 MS ecu it WILL RUN low impedance injectors... we map them every day :P

Cheers, Matt (M-tech)

[ScoobyMatt]

Rick, I dont beliebe the MS2 supprot fully sequential or cylinder trim, that will be the sequenceer which uis not yet out.

The MS2 is a good chip, but we use MS1 and have no probs what so ever. The resolution is higher on the MS2 as are the tables, but becuase the MS1 fully interpolates its not really required.

Matt

[nsdrst]

look great mate keep up the good work