4x4 sapphire cosworth forsale (now sold)
29-07-2011, 03:12 PM
#1
4x4 sapphire cosworth forsale (now sold)
have decided i want to build a 3dr track car and have found a shell, so decided to sell my sapphire cosworth.
i bought it just after christmas from a guy in Blackpool
its just about to turn 90k and has MOT till march next year and taxed till end of september
The shell has never been welded, the rear arches are completely rust free, the only bit of rust is a very small scab on the front drivers side lip.
The engine is very good, its running MSD wasted spark, has uprated fan loom. I've just fitted a brand new radtec alloy radiator. it has a pro alloy 500 intercooler.
Its running a T34.63, not very old and the engine does not smoke. When i bought it i was told it was running aprox 380 BHP and 400 lbft of torque. it goes very well.
It has the cloth interior which is in very good condition, but the door cards do have some shrinkage.
its lowered on Koni shocks and springs
Heres some pics
will put some better pics up later
looing for £7250 ono with comps or £6750 with standard sharktooth alloys running R888's on them
cheers, all comments welcome good or bad
If it doen't sell, i will break it as i should be able to get roughly the same money back for it in bits
i've decided its too good to break but would be open to px's on anything ford so WHY?
cheers Matthew
i bought it just after christmas from a guy in Blackpool
its just about to turn 90k and has MOT till march next year and taxed till end of september
The shell has never been welded, the rear arches are completely rust free, the only bit of rust is a very small scab on the front drivers side lip.
The engine is very good, its running MSD wasted spark, has uprated fan loom. I've just fitted a brand new radtec alloy radiator. it has a pro alloy 500 intercooler.
Its running a T34.63, not very old and the engine does not smoke. When i bought it i was told it was running aprox 380 BHP and 400 lbft of torque. it goes very well.
It has the cloth interior which is in very good condition, but the door cards do have some shrinkage.
its lowered on Koni shocks and springs
Heres some pics
will put some better pics up later
looing for £7250 ono with comps or £6750 with standard sharktooth alloys running R888's on them
cheers, all comments welcome good or bad
If it doen't sell, i will break it as i should be able to get roughly the same money back for it in bits
i've decided its too good to break but would be open to px's on anything ford so WHY?
cheers Matthew
Last edited by 3dr cossie; 22-01-2012 at 06:13 PM.
29-07-2011, 03:14 PM
#2
forgot to add its running siemenns 55lb injectors aswell, has uprated fuel pump, full mongoose exhaust system, uprated breather system.
i've recently fitted a new alternator, gear knob and gear gaitor. It has an RS centre on the steering wheel.
It has a paddle clutch fitted
cheers Matthew
i've recently fitted a new alternator, gear knob and gear gaitor. It has an RS centre on the steering wheel.
It has a paddle clutch fitted
cheers Matthew
Last edited by 3dr cossie; 29-07-2011 at 03:18 PM.
Trending Topics
10-08-2011, 07:34 PM
#18
just been looking through all the receipts.
A lad called Nick who used to own this car worked ar motorsport developments at the time and there are several job sheets from them.
the first sheet has listed
polish YB crankshaft bearing surfaces,
supply and fit the following:-
crankshaft main & big end bearings
crankshaft thrust washers
front and rear cranshaft oil seals
front timing cover gasket
aux shaft thrust plate
oil pump and drive
con rod bolts (std)
sump seals
timing belt & tensioner
3 bar map sensor
power steering rack (new)
cam cover half moon seals
turbocharger oil return gasket.
the second job sheet reads as follows:-
remove, overhaul & refit cylinder head with new guides, cam bearings, stem seals and recut seats.
supply and fit cometic multilayer steel gasket
supply and fit new head bolts
supply and fit new exhaust manifold gaskets
supply and fit new cometic inlet & plenum gaskets
supply and fit new coolant sensors for ecu and dash
supply and fit new cam cover gasket
supply and fit new alternator belts and powersteering belts
supply and fit 2 new heater matrix hoses, renew both matrix seals and new header tank
supply and fit new 82 degree stat
supply and fit new steering column bush
supply and fit adjustable front tca's
supply and fit new alcon paddle clutch
replace all crankcase breather hoses
live map engine with siemens 55lb injectors and closed loop lambda control.
other receipts from MSD include a new T34 turbo,
new bosch 044 fuel pump
supply and fit wasted spark conversion
theres over 25 reciepts from ford for parts
there is also thousands of pounds worth of reciepts in the history file for this car
cheers Matthew
A lad called Nick who used to own this car worked ar motorsport developments at the time and there are several job sheets from them.
the first sheet has listed
polish YB crankshaft bearing surfaces,
supply and fit the following:-
crankshaft main & big end bearings
crankshaft thrust washers
front and rear cranshaft oil seals
front timing cover gasket
aux shaft thrust plate
oil pump and drive
con rod bolts (std)
sump seals
timing belt & tensioner
3 bar map sensor
power steering rack (new)
cam cover half moon seals
turbocharger oil return gasket.
the second job sheet reads as follows:-
remove, overhaul & refit cylinder head with new guides, cam bearings, stem seals and recut seats.
supply and fit cometic multilayer steel gasket
supply and fit new head bolts
supply and fit new exhaust manifold gaskets
supply and fit new cometic inlet & plenum gaskets
supply and fit new coolant sensors for ecu and dash
supply and fit new cam cover gasket
supply and fit new alternator belts and powersteering belts
supply and fit 2 new heater matrix hoses, renew both matrix seals and new header tank
supply and fit new 82 degree stat
supply and fit new steering column bush
supply and fit adjustable front tca's
supply and fit new alcon paddle clutch
replace all crankcase breather hoses
live map engine with siemens 55lb injectors and closed loop lambda control.
other receipts from MSD include a new T34 turbo,
new bosch 044 fuel pump
supply and fit wasted spark conversion
theres over 25 reciepts from ford for parts
there is also thousands of pounds worth of reciepts in the history file for this car
cheers Matthew
